{"id":25235,"date":"2026-11-16T13:25:09","date_gmt":"2026-11-16T13:25:09","guid":{"rendered":"https:\/\/atalnetworks.com\/?p=25235"},"modified":"2026-11-16T13:25:09","modified_gmt":"2026-11-16T13:25:09","slug":"upgrade-dedicated-server-to-10gbps","status":"publish","type":"post","link":"https:\/\/atalnetworks.com\/nl\/upgrade-dedicated-server-to-10gbps\/","title":{"rendered":"Upgrading from 1Gbps to 10Gbps: A Dedicated Server Migration Checklist"},"content":{"rendered":"<p><span style=\"font-weight: 400;\">A 10Gbps upgrade can give your server more room for downloads, backups, replication, and busy traffic periods. But the change may involve more than a faster port. It can also mean a new network card, a rack move, different IP addresses, or a replacement server.<\/span><\/p>\n<p><b>To upgrade a dedicated server to 10Gbps, confirm the provider&#8217;s upgrade method, check hardware and network support, save the current configuration, and prepare recovery access. Plan any address or data changes, run acceptance tests, and keep a rollback path until the service meets your agreed targets.<\/b><\/p>\n<p><span style=\"font-weight: 400;\">We recommend treating the upgrade as a controlled service change. The goal is to improve the workload while keeping access, data, and recovery options under control.<\/span><\/p>\n<p><span style=\"font-weight: 400;\">This checklist covers three upgrade paths. Follow the steps that apply to your provider and server. The calculations are planning examples, not measured Atal Networks migration results.<\/span><\/p>\n<h2><span style=\"font-weight: 400;\">The 1Gbps to 10Gbps Upgrade Checklist<\/span><\/h2>\n<p><span style=\"font-weight: 400;\">Use this sequence to organize the work:<\/span><\/p>\n<ul>\n<li style=\"font-weight: 400;\" aria-checked=\"false\" aria-level=\"1\"><span style=\"font-weight: 400;\">Confirm which network limit the upgrade must fix.<\/span><\/li>\n<li style=\"font-weight: 400;\" aria-checked=\"false\" aria-level=\"1\"><span style=\"font-weight: 400;\">Get the provider&#8217;s exact change scope in writing.<\/span><\/li>\n<li style=\"font-weight: 400;\" aria-checked=\"false\" aria-level=\"1\"><span style=\"font-weight: 400;\">Check NIC, cable, driver, switch, and server compatibility.<\/span><\/li>\n<li style=\"font-weight: 400;\" aria-checked=\"false\" aria-level=\"1\"><span style=\"font-weight: 400;\">Save the current network and service configuration.<\/span><\/li>\n<li style=\"font-weight: 400;\" aria-checked=\"false\" aria-level=\"1\"><span style=\"font-weight: 400;\">Confirm IP, routing, firewall, and billing changes.<\/span><\/li>\n<li style=\"font-weight: 400;\" aria-checked=\"false\" aria-level=\"1\"><span style=\"font-weight: 400;\">Test backups and recovery access.<\/span><\/li>\n<li style=\"font-weight: 400;\" aria-checked=\"false\" aria-level=\"1\"><span style=\"font-weight: 400;\">Prepare data synchronization and DNS changes where needed.<\/span><\/li>\n<li style=\"font-weight: 400;\" aria-checked=\"false\" aria-level=\"1\"><span style=\"font-weight: 400;\">Set the maintenance window and latest rollback decision time.<\/span><\/li>\n<li style=\"font-weight: 400;\" aria-checked=\"false\" aria-level=\"1\"><span style=\"font-weight: 400;\">Carry out the agreed upgrade or migration.<\/span><\/li>\n<li style=\"font-weight: 400;\" aria-checked=\"false\" aria-level=\"1\"><span style=\"font-weight: 400;\">Run network and application acceptance tests.<\/span><\/li>\n<li style=\"font-weight: 400;\" aria-checked=\"false\" aria-level=\"1\"><span style=\"font-weight: 400;\">Monitor service health and transfer use.<\/span><\/li>\n<li style=\"font-weight: 400;\" aria-checked=\"false\" aria-level=\"1\"><span style=\"font-weight: 400;\">Retire the old setup only after the exit checks pass.<\/span><\/li>\n<\/ul>\n<p><span style=\"font-weight: 400;\">Assign an owner to each phase. Keep the evidence in one change record so the team can decide whether to proceed, pause, or recover.<\/span><\/p>\n<h2><span style=\"font-weight: 400;\">1. Confirm What the Upgrade Must Fix<\/span><\/h2>\n<p><span style=\"font-weight: 400;\">Start with the workload, not the port label. A faster connection helps when the current network capacity limits useful work. It may do little for a service limited by database queries, disk reads, CPU processing, or a slow client connection.<\/span><\/p>\n<p><span style=\"font-weight: 400;\">Record performance during the periods that matter to the business:<\/span><\/p>\n<table>\n<thead>\n<tr>\n<th><b>Baseline<\/b><\/th>\n<th><b>What to record<\/b><\/th>\n<th><b>Why it matters<\/b><\/th>\n<\/tr>\n<\/thead>\n<tbody>\n<tr>\n<td><span style=\"font-weight: 400;\">Network use<\/span><\/td>\n<td><span style=\"font-weight: 400;\">Send and receive rates, peaks, and time near the current limit<\/span><\/td>\n<td><span style=\"font-weight: 400;\">Shows whether the link is under pressure<\/span><\/td>\n<\/tr>\n<tr>\n<td><span style=\"font-weight: 400;\">Application health<\/span><\/td>\n<td><span style=\"font-weight: 400;\">Response times, errors, and completed work<\/span><\/td>\n<td><span style=\"font-weight: 400;\">Connects the upgrade to user experience<\/span><\/td>\n<\/tr>\n<tr>\n<td><span style=\"font-weight: 400;\">Processor<\/span><\/td>\n<td><span style=\"font-weight: 400;\">Total and per-core use<\/span><\/td>\n<td><span style=\"font-weight: 400;\">Reveals processing limits hidden by an average<\/span><\/td>\n<\/tr>\n<tr>\n<td><span style=\"font-weight: 400;\">Opslagruimte<\/span><\/td>\n<td><span style=\"font-weight: 400;\">Read\/write rate, latency, and queue pressure<\/span><\/td>\n<td><span style=\"font-weight: 400;\">Shows whether disks can feed or receive more data<\/span><\/td>\n<\/tr>\n<tr>\n<td><span style=\"font-weight: 400;\">Transfers<\/span><\/td>\n<td><span style=\"font-weight: 400;\">Data size, duration, and useful copy rate<\/span><\/td>\n<td><span style=\"font-weight: 400;\">Provides a before-and-after comparison<\/span><\/td>\n<\/tr>\n<tr>\n<td><span style=\"font-weight: 400;\">Network quality<\/span><\/td>\n<td><span style=\"font-weight: 400;\">Drops, retransmissions, and path latency<\/span><\/td>\n<td><span style=\"font-weight: 400;\">Helps separate capacity from loss or routing issues<\/span><\/td>\n<\/tr>\n<\/tbody>\n<\/table>\n<p><span style=\"font-weight: 400;\">Set a clear success target. For example, a backup might need to finish inside a two-hour window. A file service might need to handle an agreed number of downloads without slowing its application responses.<\/span><\/p>\n<p><span style=\"font-weight: 400;\">Avoid using \u201cthe port reaches 10Gbps\u201d as the only target. Link speed is different from <\/span><b>goodput<\/b><span style=\"font-weight: 400;\">, which is the useful data received by an application. Headers, retransmissions, and other work reduce the useful rate.<\/span><\/p>\n<p><span style=\"font-weight: 400;\">For a broader comparison, see our guide to <\/span><a href=\"https:\/\/atalnetworks.com\/nl\/10gbps-vs-1gbps-dedicated-servers\/\"><span style=\"font-weight: 400;\">1Gbps vs. 10Gbps dedicated server throughput<\/span><\/a><span style=\"font-weight: 400;\">.<\/span><\/p>\n<h2><span style=\"font-weight: 400;\">2. Choose the Correct Upgrade Path<\/span><\/h2>\n<p><span style=\"font-weight: 400;\">Ask the provider what will physically and logically change. The answer determines the preparation and rollback plan.<\/span><\/p>\n<table>\n<thead>\n<tr>\n<th><b>Upgrade path<\/b><\/th>\n<th><b>Is a data copy required?<\/b><\/th>\n<th><b>Could addresses change?<\/b><\/th>\n<th><b>Main recovery dependency<\/b><\/th>\n<\/tr>\n<\/thead>\n<tbody>\n<tr>\n<td><span style=\"font-weight: 400;\">Change the port or bandwidth policy on existing hardware<\/span><\/td>\n<td><span style=\"font-weight: 400;\">Usually not for the port change itself<\/span><\/td>\n<td><span style=\"font-weight: 400;\">Confirm with the provider<\/span><\/td>\n<td><span style=\"font-weight: 400;\">Restoring the previous policy or connection<\/span><\/td>\n<\/tr>\n<tr>\n<td><span style=\"font-weight: 400;\">Replace the NIC or move the existing server<\/span><\/td>\n<td><span style=\"font-weight: 400;\">Not always<\/span><\/td>\n<td><span style=\"font-weight: 400;\">Yes, depending on the network<\/span><\/td>\n<td><span style=\"font-weight: 400;\">Hardware access, old network availability, and OS configuration<\/span><\/td>\n<\/tr>\n<tr>\n<td><span style=\"font-weight: 400;\">Move to a new server or provider<\/span><\/td>\n<td><span style=\"font-weight: 400;\">Usually, for data stored on the old server<\/span><\/td>\n<td><span style=\"font-weight: 400;\">Plan for it unless confirmed otherwise<\/span><\/td>\n<td><span style=\"font-weight: 400;\">Old service availability and a consistent data recovery path<\/span><\/td>\n<\/tr>\n<\/tbody>\n<\/table>\n<h3><span style=\"font-weight: 400;\">Upgrade the Existing Port or Policy<\/span><\/h3>\n<p><span style=\"font-weight: 400;\">Some servers already have suitable network hardware but operate under a lower bandwidth limit. The provider may be able to change that limit without moving application data.<\/span><\/p>\n<p><span style=\"font-weight: 400;\">Confirm whether the work requires a switch-port change, cable change, brief link interruption, or server restart. A small provider-side change still needs testing afterward.<\/span><\/p>\n<h3><span style=\"font-weight: 400;\">Replace the NIC or Move the Server<\/span><\/h3>\n<p><span style=\"font-weight: 400;\">A physical upgrade can affect interface names, MAC addresses, drivers, and network configuration. A rack move can also place the server on another subnet.<\/span><\/p>\n<p><span style=\"font-weight: 400;\">For example, Hetzner&#8217;s documented 10G uplink process includes moving an existing server to a suitable rack and changing its IP addresses. Its documentation also identifies interface-name changes and a difference in available firewall service. Those are provider-specific details, not rules for every 10Gbps upgrade.\u00a0<\/span><\/p>\n<p><span style=\"font-weight: 400;\">Ask whether the previous hardware and port can be restored if the change fails. Physical rollback may require another maintenance window.<\/span><\/p>\n<h3><span style=\"font-weight: 400;\">Move to a New Server or Provider<\/span><\/h3>\n<p><span style=\"font-weight: 400;\">A replacement server lets you prepare much of the environment while the old service remains online. It also adds work: data transfer, software compatibility, address changes, and control of tasks running on both machines.<\/span><\/p>\n<p><span style=\"font-weight: 400;\">Keep the network upgrade separate from unrelated application or database upgrades where practical. Fewer changes make failures easier to diagnose and reverse.<\/span><\/p>\n<h2><span style=\"font-weight: 400;\">3. Check Hardware and Network Compatibility<\/span><\/h2>\n<p><span style=\"font-weight: 400;\">A 10Gbps network card is one part of the path. Confirm that the server, operating system, connection, and upstream equipment support the intended setup.<\/span><\/p>\n<h3><span style=\"font-weight: 400;\">Check the NIC, PCIe Slot, Driver, and Firmware<\/span><\/h3>\n<p><span style=\"font-weight: 400;\">Record the exact adapter model, firmware version, driver, and operating system. Confirm that the card fits the chassis and that its PCI Express connection supports the intended workload.<\/span><\/p>\n<p><span style=\"font-weight: 400;\">A physically compatible slot does not, by itself, prove the available electrical lanes or negotiated PCIe link capability.<\/span><\/p>\n<p><span style=\"font-weight: 400;\">Also check CPU use under network load. Linux can distribute network processing through NIC queues and related mechanisms, but the actual distribution depends on the hardware and configuration. More CPU cores do not automatically remove every packet-processing limit.\u00a0<\/span><\/p>\n<h3><span style=\"font-weight: 400;\">Match the Cable or Optics to Both Ends<\/span><\/h3>\n<p><span style=\"font-weight: 400;\">Identify the physical connection:<\/span><\/p>\n<ul>\n<li style=\"font-weight: 400;\" aria-level=\"1\"><b>10GBASE-T:<\/b><span style=\"font-weight: 400;\"> Copper Ethernet using suitable cabling and supported distances.<\/span><\/li>\n<li style=\"font-weight: 400;\" aria-level=\"1\"><b>SFP+ direct-attach cable:<\/b><span style=\"font-weight: 400;\"> A cable assembly supported by both connected devices.<\/span><\/li>\n<li style=\"font-weight: 400;\" aria-level=\"1\"><b>SFP+ optical modules:<\/b><span style=\"font-weight: 400;\"> Supported transceivers with matching fiber type, connectors, and optical requirements.<\/span><\/li>\n<\/ul>\n<p><span style=\"font-weight: 400;\">Do not assume a module works because it fits the port. Intel&#8217;s X520 documentation, for example, lists supported module and cable requirements for that adapter family. Check the documentation for the hardware you will actually use.\u00a0<\/span><\/p>\n<h3><span style=\"font-weight: 400;\">Check the Full Network Path<\/span><\/h3>\n<p><span style=\"font-weight: 400;\">Confirm the switch port, VLAN, public uplink, private-network connection, and provider-side rate limits. If the workload moves data through a firewall, VPN, proxy, or storage service, include that component in testing.<\/span><\/p>\n<p><span style=\"font-weight: 400;\">The remote endpoint matters too. A destination with a 1Gbps limit will not receive one transfer at 10Gbps merely because your server has a faster port.<\/span><\/p>\n<h3><span style=\"font-weight: 400;\">Keep MTU Changes Separate<\/span><\/h3>\n<p><span style=\"font-weight: 400;\">You do not need to make a blanket change to jumbo frames when upgrading to 10Gbps.<\/span><\/p>\n<p><span style=\"font-weight: 400;\">The maximum transmission unit, or MTU, controls packet size on an interface. A larger MTU needs support along the relevant path. A private network and a public Internet path can have different limits.<\/span><\/p>\n<p><span style=\"font-weight: 400;\">Record the working MTU first. If a change is required, test it separately and keep a way to restore the previous setting.<\/span><\/p>\n<h2><span style=\"font-weight: 400;\">4. Confirm Provider, IP, and Service Changes<\/span><\/h2>\n<p><span style=\"font-weight: 400;\">Get written answers before booking the maintenance window.<\/span><\/p>\n<h3><span style=\"font-weight: 400;\">Questions to Send Your Provider<\/span><\/h3>\n<ol>\n<li style=\"font-weight: 400;\" aria-level=\"1\"><span style=\"font-weight: 400;\">Is this a port-policy change, hardware replacement, rack move, or new-server deployment?<\/span><\/li>\n<li style=\"font-weight: 400;\" aria-level=\"1\"><span style=\"font-weight: 400;\">Which parts of the work require a shutdown or link interruption?<\/span><\/li>\n<li style=\"font-weight: 400;\" aria-level=\"1\"><span style=\"font-weight: 400;\">Will IPv4 addresses, IPv6 addresses, gateways, or VLANs change?<\/span><\/li>\n<li style=\"font-weight: 400;\" aria-level=\"1\"><span style=\"font-weight: 400;\">Will interface names or MAC addresses change?<\/span><\/li>\n<li style=\"font-weight: 400;\" aria-level=\"1\"><span style=\"font-weight: 400;\">Who updates the operating system&#8217;s network configuration?<\/span><\/li>\n<li style=\"font-weight: 400;\" aria-level=\"1\"><span style=\"font-weight: 400;\">Will the current firewall and DDoS services remain available?<\/span><\/li>\n<li style=\"font-weight: 400;\" aria-level=\"1\"><span style=\"font-weight: 400;\">Is the 10Gbps allocation shared, dedicated, or subject to another rate policy?<\/span><\/li>\n<li style=\"font-weight: 400;\" aria-level=\"1\"><span style=\"font-weight: 400;\">What transfer allowance and excess-use charges apply?<\/span><\/li>\n<li style=\"font-weight: 400;\" aria-level=\"1\"><span style=\"font-weight: 400;\">Which console, rescue, and remote-hands services are available during the window?<\/span><\/li>\n<li style=\"font-weight: 400;\" aria-level=\"1\"><span style=\"font-weight: 400;\">Can the previous setup be restored, and how long would that take?<\/span><\/li>\n<\/ol>\n<p><span style=\"font-weight: 400;\">The answers should refer to the server and order you are changing, not just the provider&#8217;s general product page.<\/span><\/p>\n<h3><span style=\"font-weight: 400;\">Map Dependencies on the Old Address<\/span><\/h3>\n<p><span style=\"font-weight: 400;\">An IP change affects more than the website&#8217;s DNS record.<\/span><\/p>\n<table>\n<thead>\n<tr>\n<th><b>Dependency<\/b><\/th>\n<th><b>Check before cutover<\/b><\/th>\n<\/tr>\n<\/thead>\n<tbody>\n<tr>\n<td><span style=\"font-weight: 400;\">DNS<\/span><\/td>\n<td><span style=\"font-weight: 400;\">A and AAAA records point to the intended destinations<\/span><\/td>\n<\/tr>\n<tr>\n<td><span style=\"font-weight: 400;\">Outbound traffic<\/span><\/td>\n<td><span style=\"font-weight: 400;\">External APIs and partners allow the new source address<\/span><\/td>\n<\/tr>\n<tr>\n<td><span style=\"font-weight: 400;\">Firewall rules<\/span><\/td>\n<td><span style=\"font-weight: 400;\">Host and provider rules cover the new network<\/span><\/td>\n<\/tr>\n<tr>\n<td><span style=\"font-weight: 400;\">VPN peers<\/span><\/td>\n<td><span style=\"font-weight: 400;\">Peer endpoints and access rules use the correct addresses<\/span><\/td>\n<\/tr>\n<tr>\n<td><span style=\"font-weight: 400;\">CDN or load balancer<\/span><\/td>\n<td><span style=\"font-weight: 400;\">The origin or backend points to the intended server<\/span><\/td>\n<\/tr>\n<tr>\n<td><span style=\"font-weight: 400;\">Monitoring and backups<\/span><\/td>\n<td><span style=\"font-weight: 400;\">Agents and remote systems reach the new host<\/span><\/td>\n<\/tr>\n<tr>\n<td><span style=\"font-weight: 400;\">Licenses<\/span><\/td>\n<td><span style=\"font-weight: 400;\">Any IP-bound license supports the move<\/span><\/td>\n<\/tr>\n<tr>\n<td><span style=\"font-weight: 400;\">email<\/span><\/td>\n<td><span style=\"font-weight: 400;\">Relevant PTR, SPF, and sending-host settings match the new setup<\/span><\/td>\n<\/tr>\n<tr>\n<td><span style=\"font-weight: 400;\">Application configuration<\/span><\/td>\n<td><span style=\"font-weight: 400;\">No required service still binds to or calls the old address<\/span><\/td>\n<\/tr>\n<\/tbody>\n<\/table>\n<p><span style=\"font-weight: 400;\">Provider-assigned addresses are not automatically portable between companies. If you use your own address space, arrange routing and authorization with the new provider before relying on it.<\/span><\/p>\n<p><span style=\"font-weight: 400;\">Use our <\/span><a href=\"https:\/\/atalnetworks.com\/nl\/ip-reputation-and-geolocation-checks-before-migration\/\"><span style=\"font-weight: 400;\">IP reputation and geolocation checks before migration<\/span><\/a><span style=\"font-weight: 400;\"> when assessing new addresses.<\/span><\/p>\n<h3><span style=\"font-weight: 400;\">Check Billing as a Separate Requirement<\/span><\/h3>\n<p><span style=\"font-weight: 400;\">Port speed and monthly data transfer are different measurements. A 10Gbps connection may have a fixed transfer allowance, usage-based charges, or unmetered terms.<\/span><\/p>\n<p><span style=\"font-weight: 400;\">Record setup fees, hardware work, IP fees, transfer charges, and the cost of keeping two servers online. Confirm the billing start date and the notice required to cancel the old service.<\/span><\/p>\n<p><span style=\"font-weight: 400;\">A faster port does not itself create more traffic, but it can let a workload consume its allowance sooner.<\/span><\/p>\n<h2><span style=\"font-weight: 400;\">5. Prepare Backups, Data, and Recovery Access<\/span><\/h2>\n<p><span style=\"font-weight: 400;\">Before changing the network, make sure you can recover without the normal connection.<\/span><\/p>\n<h3><span style=\"font-weight: 400;\">Save the Current Configuration<\/span><\/h3>\n<p><span style=\"font-weight: 400;\">Keep a secure record of:<\/span><\/p>\n<ul>\n<li style=\"font-weight: 400;\" aria-level=\"1\"><span style=\"font-weight: 400;\">Interface names, MAC addresses, and IP settings.<\/span><\/li>\n<li style=\"font-weight: 400;\" aria-level=\"1\"><span style=\"font-weight: 400;\">Routes, gateways, VLANs, bonds, and bridges.<\/span><\/li>\n<li style=\"font-weight: 400;\" aria-level=\"1\"><span style=\"font-weight: 400;\">Host and provider firewall rules.<\/span><\/li>\n<li style=\"font-weight: 400;\" aria-level=\"1\"><span style=\"font-weight: 400;\">Service bindings and listening ports.<\/span><\/li>\n<li style=\"font-weight: 400;\" aria-level=\"1\"><span style=\"font-weight: 400;\">DNS records and external address dependencies.<\/span><\/li>\n<li style=\"font-weight: 400;\" aria-level=\"1\"><span style=\"font-weight: 400;\">Software versions, credentials, certificates, and required licenses.<\/span><\/li>\n<\/ul>\n<p><span style=\"font-weight: 400;\">Store recovery instructions somewhere accessible if the server is offline. Test the remote console or provider rescue method before the window begins.<\/span><\/p>\n<h3><span style=\"font-weight: 400;\">Test a Backup Restore<\/span><\/h3>\n<p><span style=\"font-weight: 400;\">A completed backup job is not the same as a working restore.<\/span><\/p>\n<p><span style=\"font-weight: 400;\">Restore the required data and configuration into a separate environment. Check that the application can use them. Record how long recovery takes and which credentials or external services it needs.<\/span><\/p>\n<p><span style=\"font-weight: 400;\">Define the recovery point objective, or RPO, as the data loss the service can tolerate. Define the recovery time objective, or RTO, as the time allowed to restore service. Use these limits when choosing the migration and rollback method.<\/span><\/p>\n<h3><span style=\"font-weight: 400;\">Prepare the Initial Copy and Final Sync<\/span><\/h3>\n<p><span style=\"font-weight: 400;\">For a new-server migration, copy stable data before the maintenance window. Plan a separate step for data that changes while production remains active.<\/span><\/p>\n<p><span style=\"font-weight: 400;\">Use database-supported backup or replication methods. Copying live database files with a general file-transfer tool does not, by itself, prove that the resulting database is consistent.<\/span><\/p>\n<p><span style=\"font-weight: 400;\">Include uploaded files, queue contents, mail, and other local state. Decide which server will hold the authoritative copy at each stage.<\/span><\/p>\n<h3><span style=\"font-weight: 400;\">Estimate Transfer Time From the Slowest Part of the Path<\/span><\/h3>\n<p><span style=\"font-weight: 400;\">The old server&#8217;s 1Gbps connection may still limit the initial copy to a new 10Gbps server.<\/span><\/p>\n<p><span style=\"font-weight: 400;\">Use measured useful copy throughput:<\/span><\/p>\n<p><b>Copy time in seconds = data size in bytes \u00d7 8 \u00f7 useful throughput in bits per second<\/b><\/p>\n<p><span style=\"font-weight: 400;\">For one decimal terabyte at a measured useful rate of 800Mbps:<\/span><\/p>\n<p><b>1,000,000,000,000 \u00d7 8 \u00f7 800,000,000 = 10,000 seconds<\/b><\/p>\n<p><span style=\"font-weight: 400;\">That is about <\/span><b>2 hours 47 minutes<\/b><span style=\"font-weight: 400;\">. Add time for final changes, consistency checks, and application work.<\/span><\/p>\n<p><span style=\"font-weight: 400;\">This is an illustrative calculation. Storage speed, file count, encryption, compression, and competing traffic can change the actual result. If your input already measures useful copy throughput, do not subtract protocol overhead from it again.<\/span><\/p>\n<h2><span style=\"font-weight: 400;\">6. Prepare DNS and the Maintenance Window<\/span><\/h2>\n<p><span style=\"font-weight: 400;\">DNS work is necessary only where the relevant destination changes. A port upgrade that keeps the same addresses may need no DNS change at all.<\/span><\/p>\n<h3><span style=\"font-weight: 400;\">Lower the TTL Before the Address Change<\/span><\/h3>\n<p><span style=\"font-weight: 400;\">The DNS time to live, or TTL, tells resolvers how long an answer can remain cached. Lowering the TTL does not shorten the lifetime of an answer already cached under the previous value. Cloudflare documents this behavior and recommends reducing the TTL ahead of planned changes.\u00a0<\/span><\/p>\n<p><span style=\"font-weight: 400;\">For example, if the old TTL is 24 hours, changing it to five minutes immediately before cutover does not make all old answers expire within five minutes. Allow time for the earlier cache period before switching the address.<\/span><\/p>\n<p><span style=\"font-weight: 400;\">Existing application connections can also continue using the old server. Plan how that traffic will be handled while new connections move.<\/span><\/p>\n<p><span style=\"font-weight: 400;\">An address change does not require a domain registrar move. If the domain and page URLs stay the same, an IP-only migration does not call for URL redirects by itself.<\/span><\/p>\n<h3><span style=\"font-weight: 400;\">Prepare a Short Change Record<\/span><\/h3>\n<table>\n<thead>\n<tr>\n<th><b>Field<\/b><\/th>\n<th><b>What to record<\/b><\/th>\n<\/tr>\n<\/thead>\n<tbody>\n<tr>\n<td><span style=\"font-weight: 400;\">Scope<\/span><\/td>\n<td><span style=\"font-weight: 400;\">Server, services, and upgrade path<\/span><\/td>\n<\/tr>\n<tr>\n<td><span style=\"font-weight: 400;\">Owner<\/span><\/td>\n<td><span style=\"font-weight: 400;\">Person responsible for the change<\/span><\/td>\n<\/tr>\n<tr>\n<td><span style=\"font-weight: 400;\">Provider contact<\/span><\/td>\n<td><span style=\"font-weight: 400;\">Ticket and contact method for the window<\/span><\/td>\n<\/tr>\n<tr>\n<td><span style=\"font-weight: 400;\">Schedule<\/span><\/td>\n<td><span style=\"font-weight: 400;\">Start time, time zone, and expected finish<\/span><\/td>\n<\/tr>\n<tr>\n<td><span style=\"font-weight: 400;\">Data control<\/span><\/td>\n<td><span style=\"font-weight: 400;\">Which environment may accept writes at each stage<\/span><\/td>\n<\/tr>\n<tr>\n<td><span style=\"font-weight: 400;\">Test lead<\/span><\/td>\n<td><span style=\"font-weight: 400;\">Person checking the acceptance results<\/span><\/td>\n<\/tr>\n<tr>\n<td><span style=\"font-weight: 400;\">Rollback decision-maker<\/span><\/td>\n<td><span style=\"font-weight: 400;\">Person authorized to stop and reverse the change<\/span><\/td>\n<\/tr>\n<tr>\n<td><span style=\"font-weight: 400;\">Recovery reserve<\/span><\/td>\n<td><span style=\"font-weight: 400;\">Time needed to carry out rollback<\/span><\/td>\n<\/tr>\n<tr>\n<td><span style=\"font-weight: 400;\">Communication<\/span><\/td>\n<td><span style=\"font-weight: 400;\">How affected users and teams receive updates<\/span><\/td>\n<\/tr>\n<\/tbody>\n<\/table>\n<p><span style=\"font-weight: 400;\">Set the latest rollback decision early enough to leave room for recovery. If the window ends at 04:00 and tested recovery needs 30 minutes, a 03:55 decision would be too late. Add any extra margin your service requires.<\/span><\/p>\n<p><span style=\"font-weight: 400;\">Use rehearsal results and the provider&#8217;s work estimate to set the schedule. Do not promise a universal five-minute or zero-downtime upgrade.<\/span><\/p>\n<h2><span style=\"font-weight: 400;\">7. Carry Out the Upgrade<\/span><\/h2>\n<p><span style=\"font-weight: 400;\">Complete the readiness checks before starting disruptive work. Confirm recovery access, current backups, provider availability, and the agreed test targets.<\/span><\/p>\n<h3><span style=\"font-weight: 400;\">Existing Server: Port, NIC, or Rack Change<\/span><\/h3>\n<p><span style=\"font-weight: 400;\">Follow the provider&#8217;s procedure for the server. Where hardware work requires a shutdown, stop the workload in its supported order.<\/span><\/p>\n<p><span style=\"font-weight: 400;\">After the change:<\/span><\/p>\n<ol>\n<li style=\"font-weight: 400;\" aria-level=\"1\"><span style=\"font-weight: 400;\">Confirm that the expected NIC and interface are present.<\/span><\/li>\n<li style=\"font-weight: 400;\" aria-level=\"1\"><span style=\"font-weight: 400;\">Check the link state and reported speed.<\/span><\/li>\n<li style=\"font-weight: 400;\" aria-level=\"1\"><span style=\"font-weight: 400;\">Apply the approved addresses, routes, and interface bindings if they changed.<\/span><\/li>\n<li style=\"font-weight: 400;\" aria-level=\"1\"><span style=\"font-weight: 400;\">Confirm host and provider firewall behavior.<\/span><\/li>\n<li style=\"font-weight: 400;\" aria-level=\"1\"><span style=\"font-weight: 400;\">Test management access from a separate connection.<\/span><\/li>\n<li style=\"font-weight: 400;\" aria-level=\"1\"><span style=\"font-weight: 400;\">Run application checks before returning the service to normal use.<\/span><\/li>\n<\/ol>\n<p><span style=\"font-weight: 400;\">Use console access for changes that could remove your network connection. A remote shell session alone is not a recovery path.<\/span><\/p>\n<h3><span style=\"font-weight: 400;\">New Server: Test Privately, Finish the Sync, and Switch Traffic<\/span><\/h3>\n<p><span style=\"font-weight: 400;\">Prepare the destination while the old server remains live. Test with the correct hostname and TLS behavior through a private test route or local name override. Testing only the raw IP address can miss virtual-host and certificate problems.<\/span><\/p>\n<p><span style=\"font-weight: 400;\">Keep production side effects controlled during testing. The new host must not send duplicate messages, charge payments, or run the same scheduled jobs independently.<\/span><\/p>\n<p><span style=\"font-weight: 400;\">During cutover:<\/span><\/p>\n<ol>\n<li style=\"font-weight: 400;\" aria-level=\"1\"><span style=\"font-weight: 400;\">Drain or pause the required traffic and jobs.<\/span><\/li>\n<li style=\"font-weight: 400;\" aria-level=\"1\"><span style=\"font-weight: 400;\">Stop writes or follow the tested replication procedure.<\/span><\/li>\n<li style=\"font-weight: 400;\" aria-level=\"1\"><span style=\"font-weight: 400;\">Complete the final data sync.<\/span><\/li>\n<li style=\"font-weight: 400;\" aria-level=\"1\"><span style=\"font-weight: 400;\">Check data consistency and replication position where applicable.<\/span><\/li>\n<li style=\"font-weight: 400;\" aria-level=\"1\"><span style=\"font-weight: 400;\">Switch the agreed DNS record, load balancer backend, or route.<\/span><\/li>\n<li style=\"font-weight: 400;\" aria-level=\"1\"><span style=\"font-weight: 400;\">Enable the intended application writers and workers in the planned order.<\/span><\/li>\n<li style=\"font-weight: 400;\" aria-level=\"1\"><span style=\"font-weight: 400;\">Watch both environments for unexpected traffic or writes.<\/span><\/li>\n<\/ol>\n<p><b>Stop before enabling production writes if final synchronization or critical application checks fail.<\/b><span style=\"font-weight: 400;\"> Once the new server accepts writes, returning to the old copy becomes a data-recovery decision as well as a network change.<\/span><\/p>\n<h2><span style=\"font-weight: 400;\">8. Run 10Gbps Acceptance Tests<\/span><\/h2>\n<p><span style=\"font-weight: 400;\">Accept the upgrade only when the network, application, and operating tasks meet the written targets.<\/span><\/p>\n<h3><span style=\"font-weight: 400;\">Check Link Speed and Connectivity<\/span><\/h3>\n<p><span style=\"font-weight: 400;\">Confirm the reported link speed at the server and, where available, the provider&#8217;s switch port. Check IPv4 and IPv6 separately. Test routes, DNS, service access, and interface errors.<\/span><\/p>\n<p><span style=\"font-weight: 400;\">Do not disable a working IPv6 path merely to hide an incomplete migration. Complete the intended configuration and check both address families that the service publishes.<\/span><\/p>\n<h3><span style=\"font-weight: 400;\">Test Network Throughput in Both Directions<\/span><\/h3>\n<p><span style=\"font-weight: 400;\">Use test endpoints with enough capacity for the target. Run one-stream and multiple-stream tests to see whether their results differ. Test sending and receiving separately before adding a bidirectional workload.<\/span><\/p>\n<p><span style=\"font-weight: 400;\">iperf3 supports reverse tests with <\/span><span style=\"font-weight: 400;\">-R<\/span><span style=\"font-weight: 400;\">, parallel streams with <\/span><span style=\"font-weight: 400;\">-P<\/span><span style=\"font-weight: 400;\">, and bidirectional tests with <\/span><span style=\"font-weight: 400;\">&#8211;bidir<\/span><span style=\"font-weight: 400;\">. Its documentation also describes rate and payload settings for UDP tests. Use the manual for the version you install.\u00a0<\/span><\/p>\n<p><span style=\"font-weight: 400;\">Record endpoints, versions, duration, stream count, direction, receiver-side goodput, CPU load, and relevant loss or retransmission data. Agree on test traffic with the provider and endpoint owner.<\/span><\/p>\n<p><span style=\"font-weight: 400;\">A public speed-test result can help diagnose a problem, but it should not be the only acceptance evidence. The remote host or path may be the limit.<\/span><\/p>\n<h3><span style=\"font-weight: 400;\">Test the Application Under Expected Load<\/span><\/h3>\n<p><span style=\"font-weight: 400;\">A passing network test does not prove that the service works.<\/span><\/p>\n<p><span style=\"font-weight: 400;\">Check the functions that matter: login, reads, writes, uploads, API requests, queue processing, scheduled tasks, and backups. Measure latency during load, not just while the server is idle.<\/span><\/p>\n<p><span style=\"font-weight: 400;\">If the server delivers files, test realistic file reads. If it encrypts VPN traffic, test the actual VPN path. If it handles databases, check query and transaction behavior.<\/span><\/p>\n<h3><span style=\"font-weight: 400;\">Use a Written Acceptance Matrix<\/span><\/h3>\n<table>\n<thead>\n<tr>\n<th><b>Check<\/b><\/th>\n<th><b>Evidence<\/b><\/th>\n<th><b>Pass condition<\/b><\/th>\n<th><b>If it fails<\/b><\/th>\n<\/tr>\n<\/thead>\n<tbody>\n<tr>\n<td><span style=\"font-weight: 400;\">Recovery access<\/span><\/td>\n<td><span style=\"font-weight: 400;\">Working console or rescue session<\/span><\/td>\n<td><span style=\"font-weight: 400;\">Required recovery method is available<\/span><\/td>\n<td><span style=\"font-weight: 400;\">Stop before disruptive work<\/span><\/td>\n<\/tr>\n<tr>\n<td><span style=\"font-weight: 400;\">Link<\/span><\/td>\n<td><span style=\"font-weight: 400;\">NIC and switch-port reports<\/span><\/td>\n<td><span style=\"font-weight: 400;\">Matches the agreed connection<\/span><\/td>\n<td><span style=\"font-weight: 400;\">Check port policy, hardware, and cabling<\/span><\/td>\n<\/tr>\n<tr>\n<td><span style=\"font-weight: 400;\">Addressing<\/span><\/td>\n<td><span style=\"font-weight: 400;\">IPv4\/IPv6 and routing tests<\/span><\/td>\n<td><span style=\"font-weight: 400;\">Intended paths work<\/span><\/td>\n<td><span style=\"font-weight: 400;\">Correct or restore the approved settings<\/span><\/td>\n<\/tr>\n<tr>\n<td><span style=\"font-weight: 400;\">Veiligheid<\/span><\/td>\n<td><span style=\"font-weight: 400;\">Required and prohibited connection tests<\/span><\/td>\n<td><span style=\"font-weight: 400;\">Rules behave as intended<\/span><\/td>\n<td><span style=\"font-weight: 400;\">Keep affected traffic closed until fixed<\/span><\/td>\n<\/tr>\n<tr>\n<td><span style=\"font-weight: 400;\">Throughput<\/span><\/td>\n<td><span style=\"font-weight: 400;\">Repeatable endpoint test results<\/span><\/td>\n<td><span style=\"font-weight: 400;\">Meets the agreed rate under stated conditions<\/span><\/td>\n<td><span style=\"font-weight: 400;\">Identify the limiting component<\/span><\/td>\n<\/tr>\n<tr>\n<td><span style=\"font-weight: 400;\">Application<\/span><\/td>\n<td><span style=\"font-weight: 400;\">Critical user-journey results<\/span><\/td>\n<td><span style=\"font-weight: 400;\">Required functions pass<\/span><\/td>\n<td><span style=\"font-weight: 400;\">Pause the move or start recovery<\/span><\/td>\n<\/tr>\n<tr>\n<td><span style=\"font-weight: 400;\">Data<\/span><\/td>\n<td><span style=\"font-weight: 400;\">Application-specific consistency checks<\/span><\/td>\n<td><span style=\"font-weight: 400;\">Meets the agreed recovery point<\/span><\/td>\n<td><span style=\"font-weight: 400;\">Stop writes and preserve both copies<\/span><\/td>\n<\/tr>\n<tr>\n<td><span style=\"font-weight: 400;\">Operations<\/span><\/td>\n<td><span style=\"font-weight: 400;\">Monitoring, backup, and job checks<\/span><\/td>\n<td><span style=\"font-weight: 400;\">Required tasks run on the correct host<\/span><\/td>\n<td><span style=\"font-weight: 400;\">Fix dependencies before closing the change<\/span><\/td>\n<\/tr>\n<\/tbody>\n<\/table>\n<p><span style=\"font-weight: 400;\">There is no universal throughput number that proves every 10Gbps server is acceptable. Set targets from the workload and service agreement. A nominal 10Gbps link also does not carry exactly 10Gbps of application payload after protocol overhead.<\/span><\/p>\n<h2><span style=\"font-weight: 400;\">9. Monitor the Service After the Upgrade<\/span><\/h2>\n<p><span style=\"font-weight: 400;\">Keep the old baseline and compare equivalent workloads. Watch interface drops, link interruptions, TCP retransmissions, CPU use, disk pressure, response times, and application errors.<\/span><\/p>\n<h3><span style=\"font-weight: 400;\">Update Alerts Without Hiding Problems<\/span><\/h3>\n<p><span style=\"font-weight: 400;\">Changing the port capacity changes the meaning of percentage utilization.<\/span><\/p>\n<p><span style=\"font-weight: 400;\">A workload sending 500Mbps uses:<\/span><\/p>\n<ul>\n<li style=\"font-weight: 400;\" aria-level=\"1\"><b>50% of a 1Gbps port.<\/b><\/li>\n<li style=\"font-weight: 400;\" aria-level=\"1\"><b>5% of a 10Gbps port.<\/b><\/li>\n<\/ul>\n<p><span style=\"font-weight: 400;\">The traffic did not fall. Only the denominator changed.<\/span><\/p>\n<p><span style=\"font-weight: 400;\">Keep absolute traffic rates alongside utilization percentages. Review alerts based on application limits, not only the new link capacity. Also confirm that monitoring follows the correct interface if its name or index changed.<\/span><\/p>\n<h3><span style=\"font-weight: 400;\">Check Old Dependencies and Transfer Costs<\/span><\/h3>\n<p><span style=\"font-weight: 400;\">Look for traffic, database connections, scheduled jobs, or backup activity still reaching the old server. Vultr&#8217;s migration guidance specifically recommends checking that old systems are no longer in use before decommissioning them.\u00a0<\/span><\/p>\n<p><span style=\"font-weight: 400;\">Monitor transfer totals against the new plan. Check the first bill for setup work, overlapping rental periods, IP charges, and any metered usage.<\/span><\/p>\n<p><span style=\"font-weight: 400;\">An observation period should cover relevant traffic peaks and scheduled tasks. A quiet hour after cutover does not prove that a nightly job or weekly process will work.<\/span><\/p>\n<h2><span style=\"font-weight: 400;\">10. Roll Back Without Losing New Data<\/span><\/h2>\n<p><span style=\"font-weight: 400;\">Write the rollback plan before the change. It should identify the trigger, decision-maker, required access, data state, and expected recovery time.<\/span><\/p>\n<p><span style=\"font-weight: 400;\">Possible triggers include loss of management access, failed critical transactions, uncertain data consistency, missing security controls, or failure to meet the agreed service target before the deadline.<\/span><\/p>\n<h3><span style=\"font-weight: 400;\">Before the New Server Accepts Writes<\/span><\/h3>\n<p><span style=\"font-weight: 400;\">If the old environment still holds the authoritative data, recovery may involve restoring the old port, route, DNS destination, or load balancer backend.<\/span><\/p>\n<p><span style=\"font-weight: 400;\">Check that clients still reaching the new destination receive the intended response. DNS changes do not move all traffic at once.<\/span><\/p>\n<p><span style=\"font-weight: 400;\">For a NIC replacement or rack move, confirm the provider can reverse the physical work. A saved configuration cannot restore a disconnected or unavailable network by itself.<\/span><\/p>\n<h3><span style=\"font-weight: 400;\">After the New Server Accepts Writes<\/span><\/h3>\n<p><span style=\"font-weight: 400;\">Do not redirect writes to an outdated database simply because the old server is still online.<\/span><\/p>\n<p><span style=\"font-weight: 400;\">Pause writes where required and preserve the new records. Use the rehearsed reverse-sync, replication, or reconciliation procedure. If no safe return path exists, recovering on the new environment may be safer than switching back to stale data.<\/span><\/p>\n<table>\n<thead>\n<tr>\n<th><b>Current state<\/b><\/th>\n<th><b>Main risk<\/b><\/th>\n<th><b>Recovery approach<\/b><\/th>\n<\/tr>\n<\/thead>\n<tbody>\n<tr>\n<td><span style=\"font-weight: 400;\">Existing server, network change only<\/span><\/td>\n<td><span style=\"font-weight: 400;\">Lost access or delayed physical reversal<\/span><\/td>\n<td><span style=\"font-weight: 400;\">Use console access and the agreed provider procedure<\/span><\/td>\n<\/tr>\n<tr>\n<td><span style=\"font-weight: 400;\">New server, no production writes<\/span><\/td>\n<td><span style=\"font-weight: 400;\">Traffic still reaching both addresses<\/span><\/td>\n<td><span style=\"font-weight: 400;\">Restore the old entry point and control the destination<\/span><\/td>\n<\/tr>\n<tr>\n<td><span style=\"font-weight: 400;\">New server with production writes<\/span><\/td>\n<td><span style=\"font-weight: 400;\">Missing or conflicting records on return<\/span><\/td>\n<td><span style=\"font-weight: 400;\">Preserve new data and reconcile before reopening writes<\/span><\/td>\n<\/tr>\n<tr>\n<td><span style=\"font-weight: 400;\">Old server canceled or erased<\/span><\/td>\n<td><span style=\"font-weight: 400;\">Previous recovery target is gone<\/span><\/td>\n<td><span style=\"font-weight: 400;\">Use tested backups or another recovery environment<\/span><\/td>\n<\/tr>\n<\/tbody>\n<\/table>\n<p><b>Changing DNS back is a traffic change. It is not a data rollback.<\/b><\/p>\n<h3><span style=\"font-weight: 400;\">Retire the Old Setup After the Exit Checks Pass<\/span><\/h3>\n<p><span style=\"font-weight: 400;\">Before canceling or erasing the old server, confirm that:<\/span><\/p>\n<ul>\n<li style=\"font-weight: 400;\" aria-level=\"1\"><span style=\"font-weight: 400;\">Required traffic and jobs have moved.<\/span><\/li>\n<li style=\"font-weight: 400;\" aria-level=\"1\"><span style=\"font-weight: 400;\">The destination handles the expected workload.<\/span><\/li>\n<li style=\"font-weight: 400;\" aria-level=\"1\"><span style=\"font-weight: 400;\">Backups from the new environment restore correctly.<\/span><\/li>\n<li style=\"font-weight: 400;\" aria-level=\"1\"><span style=\"font-weight: 400;\">Address-based integrations use the intended server.<\/span><\/li>\n<li style=\"font-weight: 400;\" aria-level=\"1\"><span style=\"font-weight: 400;\">The agreed observation period has covered relevant operating cycles.<\/span><\/li>\n<li style=\"font-weight: 400;\" aria-level=\"1\"><span style=\"font-weight: 400;\">The service owner has accepted the result.<\/span><\/li>\n<\/ul>\n<p><span style=\"font-weight: 400;\">Then remove obsolete access rules, close temporary test services, update documentation, and complete secure data removal under your retention policy.<\/span><\/p>\n<h2><span style=\"font-weight: 400;\">Veel gestelde vragen<\/span><\/h2>\n<h3><span style=\"font-weight: 400;\">Can I Upgrade to 10Gbps Without Replacing My Dedicated Server?<\/span><\/h3>\n<p><span style=\"font-weight: 400;\">Sometimes. The provider may be able to change the port policy or install a supported NIC. Other servers need a rack move or replacement. Ask for the change scope for your exact server before planning downtime or data transfer.<\/span><\/p>\n<h3><span style=\"font-weight: 400;\">Will I Keep My IP Address After the Upgrade?<\/span><\/h3>\n<p><span style=\"font-weight: 400;\">Do not assume so. A port-policy change may preserve the address, while a move to another subnet or provider can require new addresses. Get written confirmation for IPv4 and IPv6, then update every dependent system.<\/span><\/p>\n<h3><span style=\"font-weight: 400;\">How Much Downtime Should I Plan For?<\/span><\/h3>\n<p><span style=\"font-weight: 400;\">Use the provider&#8217;s work estimate and your tested cutover procedure. Include final synchronization, startup, acceptance checks, and rollback time. A new server can be prepared in parallel, but that alone does not guarantee an interruption-free move.<\/span><\/p>\n<h3><span style=\"font-weight: 400;\">Do I Need Jumbo Frames for 10Gbps?<\/span><\/h3>\n<p><span style=\"font-weight: 400;\">No. A 10Gbps connection does not require a blanket jumbo-frame change. Use an MTU supported by the actual path. Test any larger MTU separately, especially when public and private networks have different limits.<\/span><\/p>\n<h3><span style=\"font-weight: 400;\">Why Is My Server Still Limited to About 1Gbps?<\/span><\/h3>\n<p><span style=\"font-weight: 400;\">Check the negotiated link speed, provider rate policy, remote endpoint, and route. Then inspect CPU and storage limits. Compare one-stream and multiple-stream results. The slowest part of the tested path can limit the result even when the server has a 10Gbps port.<\/span><\/p>\n<h3><span style=\"font-weight: 400;\">Will a 10Gbps Destination Copy My Old Server Ten Times Faster?<\/span><\/h3>\n<p><span style=\"font-weight: 400;\">Not if the old server or network path remains limited to 1Gbps. Estimate the copy time from measured useful throughput across the full path. Data size, storage, file count, and encryption also affect the result.<\/span><\/p>\n<h3><span style=\"font-weight: 400;\">Can I Reverse the Migration by Changing DNS?<\/span><\/h3>\n<p><span style=\"font-weight: 400;\">Only part of the migration. DNS can redirect new connections after cached answers change, but it does not return new database writes or uploaded files to the old server. Protect and reconcile that data before reopening writes on the previous system.<\/span><\/p>\n<h3><span style=\"font-weight: 400;\">When Can I Cancel the Old Server?<\/span><\/h3>\n<p><span style=\"font-weight: 400;\">After the acceptance tests pass, required dependencies have moved, backups restore correctly, and the observation period covers the relevant workload cycles. Choose that period from the service&#8217;s recovery needs rather than a fixed number of days.<\/span><\/p>\n<h2><span style=\"font-weight: 400;\">Recommended Next Steps<\/span><\/h2>\n<p><span style=\"font-weight: 400;\">Start with three practical tasks:<\/span><\/p>\n<ol>\n<li style=\"font-weight: 400;\" aria-level=\"1\"><span style=\"font-weight: 400;\">Ask your provider to confirm the upgrade method, address changes, service changes, and recovery options.<\/span><\/li>\n<li style=\"font-weight: 400;\" aria-level=\"1\"><span style=\"font-weight: 400;\">Complete the acceptance matrix and rollback plan before booking the window.<\/span><\/li>\n<li style=\"font-weight: 400;\" aria-level=\"1\"><span style=\"font-weight: 400;\">Rehearse the parts you control, then schedule the change with enough time for testing and recovery.<\/span><\/li>\n<\/ol>\n<p><span style=\"font-weight: 400;\">If you are still choosing hardware, use our <\/span><a href=\"https:\/\/atalnetworks.com\/nl\/how-to-choose-a-10gbps-dedicated-server\/\"><span style=\"font-weight: 400;\">10Gbps dedicated server buying guide<\/span><\/a><span style=\"font-weight: 400;\"> to check the workload against the proposed configuration.<\/span><\/p>\n<p><span style=\"font-weight: 400;\">Planning a move to our <\/span><a href=\"https:\/\/atalnetworks.com\/nl\/10gbps-server\/\"><span style=\"font-weight: 400;\">10Gbps server options<\/span><\/a><span style=\"font-weight: 400;\">? Share your current server, traffic pattern, address requirements, and maintenance window with our team. We can discuss the available options and the change scope to confirm before you schedule the work.<\/span><\/p>","protected":false},"excerpt":{"rendered":"<p>A 10Gbps upgrade can give your server more room for downloads, backups, replication, and busy traffic periods. But the change [&hellip;]<\/p>\n","protected":false},"author":2,"featured_media":25236,"comment_status":"open","ping_status":"open","sticky":false,"template":"","format":"standard","meta":{"_acf_changed":false,"site-sidebar-layout":"default","site-content-layout":"","ast-site-content-layout":"default","site-content-style":"default","site-sidebar-style":"default","ast-global-header-display":"","ast-banner-title-visibility":"","ast-main-header-display":"","ast-hfb-above-header-display":"","ast-hfb-below-header-display":"","ast-hfb-mobile-header-display":"","site-post-title":"","ast-breadcrumbs-content":"","ast-featured-img":"","footer-sml-layout":"","ast-disable-related-posts":"","theme-transparent-header-meta":"default","adv-header-id-meta":"","stick-header-meta":"","header-above-stick-meta":"","header-main-stick-meta":"","header-below-stick-meta":"","astra-migrate-meta-layouts":"set","ast-page-background-enabled":"default","ast-page-background-meta":{"desktop":{"background-color":"var(--ast-global-color-4)","background-image":"","background-repeat":"repeat","background-position":"center center","background-size":"auto","background-attachment":"scroll","background-type":"","background-media":"","overlay-type":"","overlay-color":"","overlay-opacity":"","overlay-gradient":""},"tablet":{"background-color":"","background-image":"","background-repeat":"repeat","background-position":"center center","background-size":"auto","background-attachment":"scroll","background-type":"","background-media":"","overlay-type":"","overlay-color":"","overlay-opacity":"","overlay-gradient":""},"mobile":{"background-color":"","background-image":"","background-repeat":"repeat","background-position":"center center","background-size":"auto","background-attachment":"scroll","background-type":"","background-media":"","overlay-type":"","overlay-color":"","overlay-opacity":"","overlay-gradient":""}},"ast-content-background-meta":{"desktop":{"background-color":"var(--ast-global-color-5)","background-image":"","background-repeat":"repeat","background-position":"center center","background-size":"auto","background-attachment":"scroll","background-type":"","background-media":"","overlay-type":"","overlay-color":"","overlay-opacity":"","overlay-gradient":""},"tablet":{"background-color":"var(--ast-global-color-5)","background-image":"","background-repeat":"repeat","background-position":"center center","background-size":"auto","background-attachment":"scroll","background-type":"","background-media":"","overlay-type":"","overlay-color":"","overlay-opacity":"","overlay-gradient":""},"mobile":{"background-color":"var(--ast-global-color-5)","background-image":"","background-repeat":"repeat","background-position":"center center","background-size":"auto","background-attachment":"scroll","background-type":"","background-media":"","overlay-type":"","overlay-color":"","overlay-opacity":"","overlay-gradient":""}},"footnotes":""},"categories":[1],"tags":[],"class_list":["post-25235","post","type-post","status-publish","format-standard","has-post-thumbnail","hentry","category-enterprise-grade-server"],"acf":[],"_links":{"self":[{"href":"https:\/\/atalnetworks.com\/nl\/wp-json\/wp\/v2\/posts\/25235","targetHints":{"allow":["GET"]}}],"collection":[{"href":"https:\/\/atalnetworks.com\/nl\/wp-json\/wp\/v2\/posts"}],"about":[{"href":"https:\/\/atalnetworks.com\/nl\/wp-json\/wp\/v2\/types\/post"}],"author":[{"embeddable":true,"href":"https:\/\/atalnetworks.com\/nl\/wp-json\/wp\/v2\/users\/2"}],"replies":[{"embeddable":true,"href":"https:\/\/atalnetworks.com\/nl\/wp-json\/wp\/v2\/comments?post=25235"}],"version-history":[{"count":1,"href":"https:\/\/atalnetworks.com\/nl\/wp-json\/wp\/v2\/posts\/25235\/revisions"}],"predecessor-version":[{"id":25237,"href":"https:\/\/atalnetworks.com\/nl\/wp-json\/wp\/v2\/posts\/25235\/revisions\/25237"}],"wp:featuredmedia":[{"embeddable":true,"href":"https:\/\/atalnetworks.com\/nl\/wp-json\/wp\/v2\/media\/25236"}],"wp:attachment":[{"href":"https:\/\/atalnetworks.com\/nl\/wp-json\/wp\/v2\/media?parent=25235"}],"wp:term":[{"taxonomy":"category","embeddable":true,"href":"https:\/\/atalnetworks.com\/nl\/wp-json\/wp\/v2\/categories?post=25235"},{"taxonomy":"post_tag","embeddable":true,"href":"https:\/\/atalnetworks.com\/nl\/wp-json\/wp\/v2\/tags?post=25235"}],"curies":[{"name":"wp","href":"https:\/\/api.w.org\/{rel}","templated":true}]}}